DRS4 Forum
  DRS4 Discussion Forum, Page 1 of 45  Not logged in ELOG logo
Entry  Tue May 26 11:10:27 2020, xggg, Domino wave 
Hi Stefan,

According to the datasheet DRS_rev09, the write signal is always 16 cells wide. So when the domino wave runs in infinite mode and be stopped
by setting DENABLE low , there are always 16 cells capicitors tracking the input signal . It means that the effective sample cells is 1024-16=1008? That's
Entry  Sun May 26 13:08:52 2013, tmiron alon,  
Hallo,
I'm using DRS4 Evaluation Board Rev 4.0 and I'm trying to  change the output of the samples to be an average of  #  measurements  (1000
or even more)
    Reply  Fri Jun 7 11:44:17 2013, tmiron alon, thank you 


    
        
            Stefan Ritt wrote:
        
        
            
            
  
    Reply  Mon Jun 10 14:09:13 2013, tmiron alon, add an average ability to the Scope 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
              
    Reply  Thu Jul 4 08:32:11 2013, tmiron alon, add an average ability to the Scope 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
              
    Reply  Thu Jul 4 09:07:24 2013, tmiron alon, add an average ability to the Scope 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
              
    Reply  Thu Jul 4 10:01:06 2013, tmiron alon, add an average ability to the Scope 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
              
    Reply  Tue Jul 16 10:02:28 2013, tmiron alon, add an average ability to the Scope 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
    Reply  Sun Jul 28 09:52:25 2013, tmiron alon, add an average ability to the Scope 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
              
    Reply  Mon Aug 12 15:08:17 2013, tmiron alon, add an average ability to the Scope 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
Entry  Sat Jan 15 09:13:42 2022, student_riku, I want to know about the readout 
Hello, everyone.
I'm a student in Japan.
Please forgive me if this is a very rudimentary question.
    Reply  Wed Jan 26 06:44:11 2022, student_riku, I want to know about the readout 
Dear Stefan

Thanks a lot.

I solved it.
Entry  Wed Feb 22 11:36:51 2012, sonal, DRS4- analog pulse counting 
Hello Sir,

Regarding to analog pulse counting by using DRS4 Rev.2.0 board,
Entry  Wed Nov 30 17:48:39 2016, samridha kunwar, DRS4 Initiation 
I am having a general problem getting read back using the ROI mode.  In the transparent mode everything looks good. These are the steps that I take:

1) configure register (b"11111111",addr = "1100")

2) configure write shift register (b"11111111", addr = "1101")
    Reply  Fri Dec 2 15:32:52 2016, samridha kunwar, DRS4 Initiation 
Thanks for replying Stefan.

I was more so just concerned with the steps in the firmware when I had asked. However, yes the ROFS (1.05V) and O-OFS (0.9 V was 1.3 V earlier
but, changed this becasue of ADC input requirements) are per spec, the VDD voltages are all there and input voltages are within the rails and finally the
Entry  Wed Feb 10 02:57:55 2010, pepe sanchez lopez, Hello 
hello i am an student and i want to do my final project with drs4 board and i really can´t find how to open waveform file and how can i save or
opened many of them quickly.
if you can tell me how i will be very grateful.
Entry  Wed Dec 23 15:38:14 2015, mony orbach, Dtap stops toggling after 40msec 
Hi

the drs4 start to generate Dtap signal after reset and standard configuration.

while in reset Denable and  Dwrite are low
    Reply  Thu Dec 24 10:51:31 2015, mony orbach, Dtap stops toggling after 40msec 
my refclk is 1.25Mhz

what are the inputs and voltage you need to see?

Avdd and Dvdd are 2.5v
    Reply  Sun Dec 27 15:06:59 2015, mony orbach, Dtap stops toggling after 40msec 
Hi

We have some meesurs to show (attached)


Dtap and Denable
Dtap+Denable in zoom
Dtap + Ref+
Dtap + Dspeed


From the screen shots
    Reply  Sun Dec 27 15:41:32 2015, mony orbach, Dtap stops toggling after 40msec Dtap-Denable.gifdtap-Danable2.gifDtap-refck.gifDtap-Dspeed.gif
Hi

We have some measures to show (attached)


Dtap and Denable
Dtap+Denable in zoom
Dtap + Refck+
Dtap + Dspeed


From the screen
ELOG V3.1.5-fe60aaf