DRS4 Forum
  DRS4 Discussion Forum, Page 12 of 45  Not logged in ELOG logo
Entry  Wed Oct 14 23:53:05 2009, Armin Kolb, DRS_exam using USB Evaluation Board with OS X Makefile
For the users using a Macintosh,
after several hours the Evaluation Board is working  on my Macintosh (intel).
1) install the development package with xcode, its on the OS X installation DVD
Entry  Fri Oct 16 09:51:03 2009, Jinhong Wang, DSR4 Full Readout Mode 
Hello Mr. Stefan Ritt
          In DSR4 DATASHEET Rev.0.8 Page13, I noticed you metioned the samping should occur after
38 ns after the rising edge of SRCLK when the multiplexer is used. So what is suggested value(delay time between sampling and the rising edge of SRCLK) for
    Reply  Fri Oct 16 10:16:10 2009, Stefan Ritt, DSR4 Full Readout Mode 


    
        
            Jinhong Wang wrote:
        
        
            
            Hello Mr. Stefan Ritt
Entry  Thu May 13 19:14:27 2010, Hao Huan, DVDD Problem of DRS 4 
Hi Stefan,
    on our board some DRS chips draw a lot of current through DVDD after power-up and heat up significantly--it is true that our
board doesn't have weak pull-down resistors at DENABLE and DWRITE output pins of FPGA, so this problem might have been caused by that, but a reinitialization
    Reply  Fri May 14 08:40:14 2010, Stefan Ritt, DVDD Problem of DRS 4 


    
        
            Hao Huan wrote:
        
        
            
            Hi Stefan,
    Reply  Tue May 18 01:47:59 2010, Hao Huan, DVDD Problem of DRS 4 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
    Reply  Tue May 18 08:23:07 2010, Stefan Ritt, DVDD Problem of DRS 4 


    
        
            Hao Huan wrote:
        
        
            
            
            
    Reply  Wed May 19 02:24:12 2010, Hao Huan, DVDD Problem of DRS 4 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
    Reply  Wed May 19 09:16:02 2010, Stefan Ritt, DVDD Problem of DRS 4 


    
        
            Hao Huan wrote:
        
        
            
            
            
    Reply  Fri Jun 18 11:31:20 2010, Jinhong Wang, DVDD Problem of DRS 4 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
    Reply  Fri Jun 18 11:45:18 2010, Stefan Ritt, DVDD Problem of DRS 4 


    
        
            Jinhong Wang wrote:
        
        
            
             
    Reply  Sat Jun 19 10:09:18 2010, Jinhong Wang, DVDD Problem of DRS 4 


    
        
            Stefan Ritt wrote:
        
        
            
            
            
Entry  Mon Mar 25 11:12:53 2013, Georg Winner, Differences in Source Code 
I have noticed some differences in the source code between Windows (4.0.0) and Linux (4.0.1) Version.
drs_exam.cpp: In the windows version when setting the trigger there is no part  "if (b->GetBoardType() == 8) {...} else {...}" like
in Linux version. So under Windows drs_exam does not start readout of DRS 4 Evalutation Board V4, because it does not get the trigger, under linux the
    Reply  Thu Apr 4 11:21:04 2013, Stefan Ritt, Differences in Source Code 


    
        
            Georg Winner wrote:
        
        
            
            I have noticed some differences in the source code between Windows (4.0.0) and Linux (4.0.1) Version.
Entry  Mon Feb 4 16:42:08 2019, Hans Steiger, Different Distances between the sampling points 
Dear All,

with the older software for my V5 Board i did not have the problem, that the distance between the sampling points (in time) is not the same (e.g.
a sampling point all 200ps for 5GS/s). 
    Reply  Mon Feb 4 16:46:04 2019, Stefan Ritt, Different Distances between the sampling points 
The sampling points are NOT equidestant, they have varying bin widths of 150ps to 250ps at 5GS/s. That's due the way the DRS4 chip works. You might
have neglected that fact in the past, but that would have led to poor timing resolutions (typically 1-2ns resolution only). To get bins with the same width,
you have to treat your waveform as a real X/Y points (or better U/T), and the re-sample that cure, maybe spline-interpolated, at 200ps bins.
    Reply  Mon Feb 4 17:36:49 2019, Hans Steiger, Different Distances between the sampling points 
Sorry.... but is there a solution or a Root Macro, that reads the waveforms into a Root-Tree? I simply can not work anymore with the data. 

Can you tell me, which software was in use in early 2017?

All the best,
    Reply  Mon Feb 4 18:18:22 2019, Stefan Ritt, Different Distances between the sampling points 
 elog:361




Hans
Steiger wrote:



Sorry.... but is there a solution or a Root Macro, that reads the
Entry  Fri Jun 9 04:11:40 2023, Javier Caravaca, Different sampling rates in multi-board configuration 
Hello,

Is it possible to have different sampling rates in multi-board configuration? I tried using the scope application but I am unable to change
the sampling rate independently.
    Reply  Mon Jun 12 14:22:04 2023, Stefan Ritt, Different sampling rates in multi-board configuration 
No, that's unfortunately not possible.

Stefan




Javier
ELOG V3.1.5-fe60aaf