DRS4 Forum
  DRS4 Discussion Forum, Page 15 of 15  Not logged in ELOG logo
New entries since:Thu Jan 1 01:00:00 1970
Entry  Fri Oct 30 03:31:54 2009, Jinhong Wang, outline dimension of DRS4 QFN_package.jpg

                                                                                                           
    Reply  Wed Nov 4 14:42:22 2009, Stefan Ritt, outline dimension of DRS4 qfn76.png


    
        
            Jinhong Wang wrote:
        
        
            
            
Entry  Mon Oct 19 11:26:29 2009, Jinhong Wang, output common mode voltage of DRS4 
Hello Mr. Stifan.Ritt
       In the DSR4 datasheet, it is mentioned
that there is an additional buffer at each analog output, this buffer shifts the the differential range of -0.5V~0.5V to 0.8V~1.8V. Does it mean that this
buffer shifts a voltage of about 1.3V for the primary differential range? 
       Again for the differential
    Reply  Mon Oct 19 12:46:12 2009, Stefan Ritt, output common mode voltage of DRS4 


    
        
            Jinhong Wang wrote:
        
        
            
            Does it mean that this buffer shifts a voltage of about 1.3V for the primary differential range? 
Entry  Mon Oct 19 09:06:43 2009, Jinhong Wang, BIAS Pin of DRS4 
Dear Mr. Stefan Ritt.
         Thank u for your timely response on "DSR4 Full Readout Mode", I received it from Professor
Qi An, who is my PhD supervisor.
    Reply  Mon Oct 19 09:13:00 2009, Stefan Ritt, BIAS Pin of DRS4 


    
        
            Jinhong Wang wrote:
        
        
            
            Dear Mr. Stefan Ritt.
Entry  Fri Oct 16 09:51:03 2009, Jinhong Wang, DSR4 Full Readout Mode 
Hello Mr. Stefan Ritt
          In DSR4 DATASHEET Rev.0.8 Page13, I noticed you metioned the samping should occur after
38 ns after the rising edge of SRCLK when the multiplexer is used. So what is suggested value(delay time between sampling and the rising edge of SRCLK) for
    Reply  Fri Oct 16 10:16:10 2009, Stefan Ritt, DSR4 Full Readout Mode 


    
        
            Jinhong Wang wrote:
        
        
            
            Hello Mr. Stefan Ritt
Entry  Wed Oct 14 23:53:05 2009, Armin Kolb, DRS_exam using USB Evaluation Board with OS X Makefile
For the users using a Macintosh,
after several hours the Evaluation Board is working  on my Macintosh (intel).
1) install the development package with xcode, its on the OS X installation DVD
Entry  Wed Oct 7 17:58:20 2009, Stefan Ritt, VDD switch off speed no_res.png100ohm.png
It turned out that the VDD switch off speed plays some important role. On our VME board, we have a linear regulator, then a 4.7 uF capacitor, then the
DRS4 chip (DVDD and AVDD). When switching off the VME power, it takes quite some time to discharge the 4.7 uF capacitor, since the DRS4 chip goes into
a high impedance mode if VDD < ~1V. This gives following VDD trace:
Entry  Tue Oct 6 11:20:39 2009, Stefan Ritt, VDD instability vdd_no_cap.pngvdd_470uf.png
It has turned out that the stability of the AVDD and DVDD power supplies for the DRS4 are very critical. On the evaluation board I use a REG1117-2.5,
on our VME board I use a ADP3338-2.5 for the DVDD power supply. When the domino wave is started, the power consumption of the DRS4 chip jumps up by ~40
mA, which has to be compensated by the linear regulator. Following screen shot shows what happens:
Entry  Thu Jul 9 09:11:03 2009, Stefan Ritt, Current problems with drs_exam.cpp 
The current version of the DRS readout example program drs_exam.cpp has two problems:

    The sampling frequency cannot be changed, it will always stay in the region around 5 GSPS
    The waveform obtained by GetWave
is rotated such that the first DRS cell corresponds to the first array bin

Both problems have been fixed and the fix will be contained
Entry  Tue Jul 7 16:39:57 2009, Stefan Ritt, Power up problem and remedy typical_mode.gif
Maybe some of you have experienced that the DRS4 chip can get pretty hot after power up. After it's initialized the first time, the power consumption
goes back to normal. I finally found the cause of this problem and have a remedy. Here is the new paragraph from the updated data sheet:
During power-up, care has to be taken that the DENABLE and DWRITE signals are low. If not, the domino wave can get started before the power
Entry  Mon Apr 27 15:09:49 2009, Stefan Ritt, Amplitude and Timing calibration for DRS4 Evaluation Board uncal.pngcal.png
This is a quick notification to all users of the current DRS4 evaluation board.
As you all know, the DRS4 chip needs some calibration for each individual cell which corrects the offset and the non-equidistant width in time.
While the first evaluation boards have been shipped without this calibration, the current version of the software implements a full amplitude and timing
Entry  Mon Feb 23 09:24:24 2009, Stefan Ritt, Rise-time measurements image001.jpgimage003.jpgsingle.jpg
Many applications using the DRS4 need to measure fast rising signals, like for PMTs or MCPs. This short note shows the minimal rise-times which can be
measured with different input signal conditioning.
Evaluation Board
The evaluation board contains four passive transformers ADT1-1WT from Mini-Circuits to convert the single-ended input
Entry  Wed Feb 11 12:21:07 2009, Stefan Ritt, Corrected datasheet Rev. 0.8 
 Please note the new datasheet Rev. 0.8 available from the DRS web site. It fixes the label of pin #76, which was AGND but is actualy AVDD. The
input IN8+ is located at pin #20 and not at pin #19 as described in the old table 2.
Entry  Wed Jan 14 12:02:04 2009, Stefan Ritt, External Trigger Input requirements tap.jpg
Several people mentioned that the external trigger input (TTL) does not work on the DRS4 Evaluation Board Rev. 1.1. This is not true. The requirement
however is that the input signal must exceed approximately 1.8V. Since the input is terminated with 50 Ohms, not all TTL drivers may deliver enough current
to exceed this threshold. To verify this, the trigger signal can be monitored with an oscilloscope at test point J24. Only if the input signal exceeds
    Reply  Wed Jan 14 13:41:44 2009, Stefan Ritt, External Trigger Input requirements 
 
Another tricky issue comes from the fact that the external TTL trigger and the comparator are in a logical OR. So if the comparator level is set
such that the signal is always over the threshold, the trigger is always "on" and the TTL trigger does not have any effect. It is therefore necessary
Entry  Mon Dec 15 13:37:38 2008, Stefan Ritt, Welcome 
 Welcome to the DRS4 Discussion Forum. This forum contains information and discussions related to the DRS4 chip. Please subscribe to this forum
to receive automatic email updates. If you have any technical questions, please feel free to post it here.
ELOG V3.1.5-fe60aaf