| ID |
Date |
Author |
Subject |
Text |
 |
|
862
|
Sat Feb 12 13:06:56 2022 |
Matias Senger | Cannot trigger on pulses, have to trigger on undershoot | I am using the DRS4 board trying to measure
pulses produced by an LGAD. I have no prior
experience with this board, have just installed |
|
|
861
|
Wed Jan 26 06:44:11 2022 |
student_riku | I want to know about the readout | Dear Stefan
Thanks a lot.
I solved it. |
|
|
860
|
Tue Jan 25 14:44:49 2022 |
Thomas M. | Regarding measuring for a set time | Yes, you've got it exactly right. Thank
you, that helps a lot!
Thomas |
|
|
859
|
Tue Jan 25 14:34:42 2022 |
Stefan Ritt | Regarding measuring for a set time | drsosc is a graphical application contiously
acquiring data from the board, and drscl
is a command line tool for debugging, as |
|
|
858
|
Tue Jan 25 14:15:00 2022 |
Thomas M. | Regarding measuring for a set time | Hello,
I'm working on a project wherein
we're looking at photomultipliers. We've |
|
|
857
|
Sat Jan 15 10:50:47 2022 |
Stefan Ritt | I want to know about the readout |
student_riku |
|
|
856
|
Sat Jan 15 09:13:42 2022 |
student_riku | I want to know about the readout | Hello, everyone.
I'm a student in Japan.
Please forgive me if this is a very |
|
|
855
|
Mon Jan 3 17:13:41 2022 |
Stefan Ritt | DRS4 request assistance | 1. fDOMINO is defined as fREFCLK * 2048
2. Good values can be derived from
the evaluation board schematics: C1=4.7nF, |
|
|
854
|
Fri Dec 24 03:13:32 2021 |
Lynsey | Trouble getting PLL to lock | I also design the circuit myself. Our problem
is the same. Can we communicate？
|
|
|
853
|
Thu Dec 23 03:42:26 2021 |
Lynsey | DRS4 request assistance | Dear Sir or Madam,
Good morning，I
am using drs4 chip, and the measured fDTAP |
|
|
852
|
Tue Nov 16 08:51:14 2021 |
Stefan Ritt | V3 board, only one channel works, all components at each channel input working | A V3 boards is already 10 years old and
out of warranty. The software has no configuration
to turn channels off except the channel buttons |
|
|
851
|
Tue Nov 16 01:27:51 2021 |
Jacquelynne Vaughan | V3 board, only one channel works, all components at each channel input working | Hi everyone,
I'm still looking through the
forum for an answer to this question, but |
|
|
850
|
Fri Nov 5 01:12:10 2021 |
Jiaolong | how to acquire the stop channel with 2x4096 cascading | Thanks for your advice. The problem has
been solved by setting the srin again while reading
out from srout. |
|
|
Draft
|
Fri Nov 5 01:10:25 2021 |
Jiaolong | how to acquire the stop channel with 2x4096 cascading |
|
|
|
848
|
Wed Oct 27 08:11:42 2021 |
Stefan Ritt | Trigger multiple boards independently | I'm not sure if the rate would go up
to 2 kHz (not 2 GHz!). Depends how the USB
hub is designed. What you can do however |
|
|
847
|
Tue Oct 26 23:18:32 2021 |
Javier Caravaca | Trigger multiple boards independently | Thank you Stefan. Actually I noticed that the
source code of drs_exam was available after
I started this thread, and that was the solution |
|
|
846
|
Tue Oct 26 15:05:18 2021 |
Mehrpad Monajem | External trigger and drs_exam | Thanks for your reply.
1- I want to have a window size
of 25.6ns instead of 200ns at 5GSPS. I have |
|
|
845
|
Tue Oct 26 12:02:56 2021 |
Stefan Ritt | Trigger multiple boards independently | Unfortunately an independent operation
from a single computer is not supported by
the software. You can try to modify the drs_exam |
|
|
844
|
Tue Oct 26 12:00:51 2021 |
Stefan Ritt | External trigger and drs_exam | 1. Why should your waveform start from
0 to 5ns? I don't get your point. Whenever
you trigger a readout, you get a 200ns wide |
|
|
843
|
Tue Oct 26 10:41:46 2021 |
Mehrpad Monajem | External trigger and drs_exam | Hi Stefan,
I have two problems regarding using |
|