Hi,

I hope I'm not missing the blindingly obvious here, but I have an issue with time and date formats

Extract from my elog.cfg file:


Time format = %a %d %b %y
Date format = %d %b
Thread display = $Ticket: $System, $entry time. ($message id). $status
Preset text = [$date]
Prepend on reply = [$date] \n

I can point to places in the syntax doc where each of these lines are given.

As for the results, the thread display is (for example):

T00001: Computer, Wed 29 Aug 12. (1). Problem

However, what I get at the top of the text box in starting a new entry or replying to a previous one is

[Wed 29 Aug 12]

whereas I expected to get

[29 Aug]

Putting $date instead of $entry time in the Thread display line makes (the by now expected) no difference

I cannot see where I'm going wrong.  

TIA 

David.

 I haven't found anything in the forums about this. Apologies if its a duplicate.

I am fairly familiar with ELog, use it for multiple purposes on 5 different Virtual Servers at work. 

Currently looking to do some updates to one of the instances with the Date Type setting.

We have 17,000 entries all which have had manual entries for a Date Attribute for the last year and 8 months.

Due to regular entry errors on part of our contractors using it, (Eg: using "Aug" instead of "08", or using "-" instead of "/"), I want to change over to using the date type attribute (Type <attribute> = Date).

However the problem i found, the moment i save this in the config, and go to the list of entries, the date has changed on all of the entries to 12/31/1969. Which is BAD for our operation. So after removing the Type Date Setting the dates go back to normal.

Is there anyway to retain those dates so they display as they are and then only new entries would fall under the new date type setting?

Syntax manual didn't help much for this issue.

 Hi All, 

 maybe I missed something in the configuration, but how do I get this nice editor for HTML like the one available on this forum?

Thanks a lot for advice.

I upgraded my system, including the version of Firefox.

I normally view the topic in Threaded Collapsed mode, right click on the entry I want to reply to, to open a new
Tab.  However, I made a mistake an opened a new Window, as the two 'open' modes in Firefox swapped around.
But no worry, I thought, made my reply as usual.

However, when refreshing the topic afterwards, seemingly randomly distributed throughout the topic were
additional lines, with the latest entry showing up emboldened (but not as a clickable link), and the only
difference being the ID number which showed as 0 (zero).

Deleting the reply only caused the previous reply to show up randomly etc.

In effect, the latest entry is (randomly?) scattered throughout the topic - even in between entries older than
any in that thread, so it's not individial entries in that thread showing up.

The only way to get rid of it was to erase the whole directory, and re-install from backup (which, as it was the
first entry since the new installation, wasn't painful).  It's been fine since - but only so long as I open a
thread in a new tab, and not in a new Window.

I guess the real question is just what is added to some file - perhaps the .cfg file? - that using a separate
window causes this behavioir?  Any whay only as a new window, and given how elog is supposed to work on many
computers, why on this stand-alone computer running two sets of the same browser?

It happened once before at the end of last year during a regression backwards owing to the newer computer
failing and turning back to an older one with older OS and older firefox, where I did the same thing (in
reverse).  As I didn't investigate at that time, I still have the mystery line showing up in that topic.

Sorry this is a bit rambling, but its very hard to describe!

 We have multiple logbooks. Each user is admin user for his/her own logbook. 

I want user be able to modify config file, but no access to user setting, such as see user list, change password, new user, remove user. 

[logbook1]
Admin user = user1
Login user = user1, user2
Allow Config = user1
List Menu commands = Admin, Config

user1 click on Admin, it opens config file, when user1 click on save, user1 is brought to Config page, which has select user list on top, Change password, Remove user, New user buttons on bottom. Is there a way that admin user has access to config file, but no access to user info at all (not even presented to them).  Is there a way after user1 click save, page doesn't go to that config page?

I could put 
Deny Change password =
Deny Remove user
Deny New user

so when user1 click on those buttons, user1 will get command not allowed. However I would rather have user1 not even see that page. 

Hi,

Is it possible to disable the Previewbutton?

Regards
Ulf Olsson

I was wondering if anyone out there has had any success with importing XML data into ELOG. Using the XML schema which I derive from the EXPORT data from ELOG into XML format or creating the file from scratch, I either blowup the system and have to restart elogd or it doesn't work and says, XML file doesn't contain ELOG_LIST element (which I create and it still doesn't work).

Basically, I am trying to take spreadsheet data, convert it into XML and upload it as a logbook so I don't have to perform lots of data entry. I also tried .CSV but have had no luck. 

Any thoughts or ideas? 

Hi,

Why is the color of an inputfield changing when I have changed the size and width?

I have attached a example.

Regards
/UlfO