| ID |
Date |
Author |
Subject |
Text |
 |
|
618
|
Fri Jun 9 09:44:33 2017 |
Rebecca Schmitz | AND Trigger problems with 2-3 channels | Hello,
It
seems that a coincidence with two fixed channels |
|
|
617
|
Thu Jun 8 15:52:20 2017 |
Stefan Ritt | AND Trigger problems with 2-3 channels | Can you post a screenshot where I can see
the channel waveforms, the configuration
and the trigger settings? |
|
|
616
|
Thu Jun 8 14:26:23 2017 |
Rebecca Schmitz | AND Trigger problems with 2-3 channels | Hello,
I work with the DRS4 Evaluation
Board V5 and I have a problem with the software. |
|
|
615
|
Tue May 30 21:22:10 2017 |
Esperienza Giove | Setting input range | Thank you
|
|
|
614
|
Tue May 30 21:00:26 2017 |
Stefan Ritt | Setting input range | See elog:531
|
|
|
613
|
Tue May 30 20:45:30 2017 |
Esperienza Giove | Setting input range | Hello,
is it possible to set a completely
negative input range like -1 to 0 or -0.95 |
|
|
612
|
Fri May 26 08:48:25 2017 |
Stefan Ritt | Invalid magic number 0000 | There is no other way to reset the board.
As I said, people running this under Windows
or MacOS are fine, so maybe this calls for |
|
|
611
|
Thu May 25 20:20:57 2017 |
Esperienza Giove | Invalid magic number 0000 | Hello, thanks for your answer. Unluckily
if i try to reset in this way it keeps hanging
musb_write: requested |
|
|
610
|
Thu May 25 20:17:41 2017 |
Esperienza Giove | Invalid magic number 0000 | Hello, thanks for your answer. Unluckily
if i try to reset in this way it keeps hanging
musb_write: requested |
|
|
609
|
Tue May 23 10:24:47 2017 |
Stefan Ritt | Invalid magic number 0000 | Under linux, many people observed that
the USB connection is unstable to the evaluation
board. This must be related to the linux |
|
|
608
|
Mon May 22 18:27:56 2017 |
Esperienza Giove | Invalid magic number 0000 | Hello everybody!
After some times i init my board,
or if i stop the program during the acquisition, |
|
|
607
|
Thu Apr 20 06:30:13 2017 |
Strahinja Lukic | Wave rotation during transfer from the board? | Thanks.
Strahinja
|
|
|
606
|
Wed Apr 19 12:17:25 2017 |
Stefan Ritt | Wave rotation during transfer from the board? | This is correct. Actually the amplitude
array is rotated already inside the DRS4
chip. So the readout starts with the stop |
|
|
605
|
Sat Apr 15 03:48:31 2017 |
Strahinja Lukic | Wave rotation during transfer from the board? | I don't know if this question is already
documented elsewhere.
I am developing a DAQ code for |
|
|
604
|
Thu Apr 13 17:10:58 2017 |
Christian Farina | Stand-alone Time Calibration for PSI Board | Thank you for your help Stefan. I will
try to get the TC part isolated.
|
|
|
603
|
Thu Apr 13 17:02:01 2017 |
Stefan Ritt | Stand-alone Time Calibration for PSI Board | Than you can try to isolate the code. Note
that different SCAs might work differently.
Like the DRS4 has a channel-to-channel jitter |
|
|
602
|
Thu Apr 13 16:54:32 2017 |
Christian Farina | Stand-alone Time Calibration for PSI Board | Hi Stefan,
Thank you for your reply. I have
read the paper already. I looked through |
|
|
601
|
Thu Apr 13 16:50:18 2017 |
Stefan Ritt | Stand-alone Time Calibration for PSI Board | Hard to say. Timing calibration is quite
delicate. If you start from scratch, better
read this paper: https://arxiv.org/abs/1405.4975 |
|
|
600
|
Thu Apr 13 16:42:21 2017 |
Christian Farina | Stand-alone Time Calibration for PSI Board | Hello everybody,
I was trying to create a stand-alone
program that would perform a time calibration |
|
|
599
|
Tue Apr 11 09:41:44 2017 |
Stefan Ritt | drs4 registers behaviour | What I do is the following: Have the RESET
input unconnected. When you power up, this
makes an internal reset during the power |
|