DRS4 Forum
  DRS4 Discussion Forum, Page 1 of 42  Not logged in ELOG logo
ID Date Author Subject Text Attachments
  852   Tue Nov 16 08:51:14 2021 Stefan RittV3 board, only one channel works, all components at each channel input workingA V3 boards is already 10 years old and
out of warranty. The software has no configuration
to turn channels off except the channel buttons
  
  851   Tue Nov 16 01:27:51 2021 Jacquelynne VaughanV3 board, only one channel works, all components at each channel input workingHi everyone,

I'm still looking through the
forum for an answer to this question, but
  
  850   Fri Nov 5 01:12:10 2021 Jiaolonghow to acquire the stop channel with 2x4096 cascading Thanks for your advice. The problem has
been solved by setting the srin again while reading
out from srout.
  
  Draft   Fri Nov 5 01:10:25 2021 Jiaolonghow to acquire the stop channel with 2x4096 cascading  




  
  848   Wed Oct 27 08:11:42 2021 Stefan RittTrigger multiple boards independentlyI'm not sure if the rate would go up
to 2 kHz (not 2 GHz!). Depends how the USB
hub is designed. What you can do however
  
  847   Tue Oct 26 23:18:32 2021 Javier CaravacaTrigger multiple boards independentlyThank you Stefan. Actually I noticed that the
source code of drs_exam was available after
I started this thread, and that was the solution
  
  846   Tue Oct 26 15:05:18 2021 Mehrpad MonajemExternal trigger and drs_examThanks for your reply.

1- I want to have a window size
of 25.6ns instead of 200ns at 5GSPS. I have
  
  845   Tue Oct 26 12:02:56 2021 Stefan RittTrigger multiple boards independentlyUnfortunately an independent operation
from a single computer is not supported by
the software. You can try to modify the drs_exam
  
  844   Tue Oct 26 12:00:51 2021 Stefan RittExternal trigger and drs_exam1. Why should your waveform start from
0 to 5ns? I don't get your point. Whenever
you trigger a readout, you get a 200ns wide
  
  843   Tue Oct 26 10:41:46 2021 Mehrpad MonajemExternal trigger and drs_examHi Stefan,


I have two problems regarding using
  
  842   Mon Oct 25 18:48:04 2021 Javier CaravacaTrigger multiple boards independentlyHello,

I recently acquired 4 DRS4 boards
and I wanted to ask if it was possible to
  
  841   Fri Oct 15 06:15:53 2021 Keita Mizukoshilivetime (or deadtime) of DRS4 evaluation boardThank you very much.




  
  840   Thu Oct 14 18:42:31 2021 Stefan Rittlivetime (or deadtime) of DRS4 evaluation boardI would say not exactly, but it's a
good approximation.

  
  839   Thu Oct 14 18:03:52 2021 Keita Mizukoshilivetime (or deadtime) of DRS4 evaluation boardThank you very much for your response.
Excuse me for my very stupid confirmation.
If I take N events finally and the
  
  838   Thu Oct 14 15:25:07 2021 Stefan Rittlivetime (or deadtime) of DRS4 evaluation boardThe one thing you can do easily is to look
at the scaler values. If one channel counts
all physical events, and you have all read
  
  837   Thu Oct 14 15:19:00 2021 Keita Mizukoshilivetime (or deadtime) of DRS4 evaluation boardDear experts,

 

I would like to use the DRS4 evaluation
  
  835   Sat Sep 18 15:48:30 2021 Stefan Rittdrs_exam_multi with non-v4 boards, default configurationHi,

please note the the evaluation
board is what it says, a board to evaluate
  
  834   Sat Sep 18 15:47:50 2021 Stefan Ritthow to acquire the stop channel with 2x4096 cascading The problem must be on your side, since
the Write Shift Register readout works in
other applications with the DRS4 chip. So
  
  833   Thu Sep 16 19:04:06 2021 Patrick Moriishi Freemandrs_exam_multi with non-v4 boards, default configurationHello, 

I made a modified version drs_exam_multi.cpp,
but ran into an issue when running.  When
  
  832   Mon Sep 6 14:42:23 2021 Jiaolonghow to acquire the stop channel with 2x4096 cascading Hi Steffan,

    I have a question
about how to acquire the stop channel: 
  
ELOG V3.1.4-80633ba