ID |
Date |
Author |
Subject |
Text |
 |
|
500
|
Mon Apr 4 11:31:34 2016 |
Stefan Ritt | DRS Oscilloscope freezing after a long run | Dear Daniel,
sorry my late reply, I'm pretty
busy these days. The behavior you report |
|
|
499
|
Sun Apr 3 22:34:28 2016 |
Abaz Kryemadhi | Trigger on the And of a positive and negative signal | Thanks, great!
|
|
|
498
|
Sun Apr 3 22:10:19 2016 |
Chris Thompson | Trigger on the And of a positive and negative signal | No there are no other components. I put
a photo of the inverter with its cables SMA
and one end, BNC at the other. You can see |
|
|
497
|
Sat Apr 2 17:22:34 2016 |
Abaz Kryemadhi | Trigger on the And of a positive and negative signal | Thanks again, this is very
useful, just another question did you
put any other passive elements in the circuit |
|
|
496
|
Sat Apr 2 11:41:07 2016 |
Stefan Ritt | Question about timimng calibration | The evaluation board normally has 1024
bins per channel. We offer an option with
2048 bins using channel cascading, to capture |
|
|
495
|
Sat Apr 2 11:21:10 2016 |
Felix Bachmair | Question about timimng calibration | Hi,
I am trying to understand some
details about the timing calibration. |
|
|
494
|
Fri Apr 1 22:09:07 2016 |
Chris Thompson | Trigger on the And of a positive and negative signal | The coilcraft part number is: JA4220-ALB.
Iordered two of them and they were sent as
free samples. You might want to buy some |
|
|
493
|
Fri Apr 1 01:30:40 2016 |
Abaz Kryemadhi | Trigger on the And of a positive and negative signal | Hi Chris,
I am looking at Sensl SiPMs
as well, can you send the part number |
|
|
492
|
Thu Mar 31 20:48:00 2016 |
Chris Thompson | Trigger on the And of a positive and negative signal | I needed a fast pulse inverter in order
to feed signals from the recent SensL SiPMs
into a conventional CFD which only accepted |
|
|
491
|
Thu Mar 31 20:38:05 2016 |
Abaz Kryemadhi | Trigger on the And of a positive and negative signal | Thanks, that looks just fine.
|
|
|
490
|
Thu Mar 31 20:34:25 2016 |
Stefan Ritt | Trigger on the And of a positive and negative signal | Here is one (SI 100): https://www.picoquant.com/products/category/accessories/adapters-splitters-cables-various-accessories-for-photon-counting-setups
|
|
|
489
|
Thu Mar 31 19:44:38 2016 |
Abaz Kryemadhi | Trigger on the And of a positive and negative signal | Ok, thanks! do you know an easy in-line
inverter like mini-circuit or digikey?
Can also redesign the detector I gues to |
|
|
488
|
Thu Mar 31 19:35:06 2016 |
Stefan Ritt | Trigger on the And of a positive and negative signal | No. You have to use an inverter for one
of your signals.
Stefan |
|
|
487
|
Thu Mar 31 19:30:26 2016 |
Abaz Kryemadhi | Trigger on the And of a positive and negative signal | I would like to be able to trigger in this
fashon: channel 0 > 0.1 and. channel
1< -0.1, because I have a positive |
|
|
486
|
Tue Mar 22 12:54:41 2016 |
Stefan Ritt | | Yes this is correct. But it is a sample-and-hold
circuit. So the sampling cell follows the
input for 3.2 ns, then samples and holds |
|
|
485
|
Mon Mar 21 10:38:27 2016 |
Daniel Dribin | DRS Oscilloscope freezing after a long run | Dear Stefan Ritt,
I am using a DRS4 v5 to do timing
measurements of Positron lifetime. I use |
|
|
484
|
Fri Mar 11 19:50:18 2016 |
Dominik Neise | | Hello Stefan,
I just stumbled again over a phrase
in the DRS4 datasheet I never really understood, |
|
|
483
|
Wed Mar 9 09:57:20 2016 |
Christian D | LabView | Hi,
I would like to use the DRS4 board
with LabView for fast readout. |
|
|
482
|
Mon Feb 29 14:09:21 2016 |
Stefan Ritt | two DRS4 boards configuration with 2048 samples each | The multi-board mode has never been tested with
2048 samples, so is very likely not to work.
I don't know yet how much work this will |
|
|
481
|
Mon Feb 29 13:33:06 2016 |
Dmitry Hits | two DRS4 boards configuration with 2048 samples each | Dear Stefan,
I daisy-chained two boards (master
sn#: 2514 - slave sn#: 2513) each with 2048 |
|