| ID |
Date |
Icon |
Author |
Author Email |
Category |
OS |
ELOG Version |
Subject |
|
69678
|
Wed Jul 26 14:43:48 2023 |
 | Stefan Ritt | stefan.ritt@psi.ch | Info | Linux | Windows | Mac OSX | All | Other | 3.1.4 | Re: export the entries from ELOG to ECSS Word document (Manifacturing Report) |
You can export logbook entries into a CSV file, then load it into Excel.
Stefan
| Manuela Rigano wrote: |
|
Thanks a lot Stefan,
I asked if it is possible, in general, to create a connection and automatically fill in the tables of a report, or export the data into excell tables to then be connected to the report, having in our case about 24 process tables to be filled in with data or validation, for each report. If the compilation is not automatic, after having compiled the elog in each phase of the processing, the manifacturing report will then have to be compiled manually.
We use elog, having already used it in MEG We must then compulsorily also make manufacturing and test reports. The expected space-type documentation format for these documents is in word.
Below is a small example of a test table, with just a few steps.
Thanks again
Manuela
|
POWER INTERFACE VERIFICATION TEST
|
|
STEP
|
Description
|
Expected Value
|
Measured value
|
Remarks
|
-
|
Power-On Ixxxx
|
|
|
|
-
|
Test communications with ...
|
|
|
|
-
|
Command xxxx to switch-on the value ….V DC/DC
|
|
|
|
-
|
Configure a multimeter to measure voltage
|
|
|
|
-
|
Use the multimeter to check ..V interface. Connect multimeter positive prove to pin x, and negative prove to pin y of yyyy connector
|
Volts: x.xV ≤ ___ ≤ y.yV
|
|
|
-
|
Repeat operation between pins z and q of …
|
Volts: 5. 097V ≤ ______ ≤ 5.252V
|
|
|
-
|
Command xxxx to switch-on the ..V DC/DC
|
|
|
|
-
|
Use the multimeter to check ..V interface. Connect multimeter positive prove to pin xx, and negative prove to pin yy of yyyy connector
|
Volts: x.x V ≤ ______ ≤ y.y V
|
|
|
-
|
Power-Off xxx
|
|
|
|
-
|
Re-connect harness to zzzz through yyyy connector
|
|
|
|
-
|
Power-On xxx
|
|
|
|
-
|
Verify ..V input voltage. Check final voltage
|
Final Volts @ ..V: x.x V ≤ __ ≤ 5y.yV
|
|
|
-
|
Verify ..V power consumption
|
Consumption @ ..V: x.x< _ < y.y W
|
|
|
-
|
|
|
|
|
| Stefan Ritt wrote: |
|
You can just copy-and-paste an elog entry into Word. I tested it here wiht a simple table:
Did a copy-and-paste to Word, and got the thing below.
Best,
Stefan
| Manuela Rigano wrote: |
|
HI,
Is there a way to export the ELOG entries to a file like Microsoft Word?
For ECSS-type documents for space missions, I have to report the data that we enter in the ELOG in a Manufacturing Report, foreseen for ECSS, in word format. It's possible to do it?
The data has to go into tables, inserted in the world file, called "as run procedure".
Is it possible to connect the elog to a report template so that it automatically generates the manufacturing report? Or link the tables placed in it so that they are automatically filled in?
Thank you so much
Manuela
|
|
|
|
|
69698
|
Fri Oct 6 11:19:34 2023 |
 | Michael | woegerbauer.micha@gmail.com | Question | Windows | 3.1.4 | Filtered browsing |
Hi,
is there a trick to get "Filtered browsing" working?
If i am on the first entry and i checked the checkbox of one Attribute, the next entry is still the second one and not the next with the same Attribute. |
|
69703
|
Mon Oct 23 15:20:32 2023 |
| Germano Massullo | germano.massullo@cern.ch | Question | Linux | 3.1.4 | read-only elog server |
Good day. I am writing this post to ask how I can turn an elog website into a read-only version that will stay online for historical documention purposes.
I tried to search on Elog documentation but I had no success
Thank you and have a nice day |
|
69704
|
Mon Oct 23 16:15:06 2023 |
| Stefan Ritt | Usestefan.ritt@psi.ch | Question | Linux | 3.1.4 | Re: read-only elog server |
Use
Menu commands = List, Find, Help
to remove all command which let you create or edit entries (New, Reply, Edit, ...)
Then do the same with "List menu commands = ..."
/Stefan
| Germano Massullo wrote: |
|
Good day. I am writing this post to ask how I can turn an elog website into a read-only version that will stay online for historical documention purposes.
I tried to search on Elog documentation but I had no success
Thank you and have a nice day
|
|
|
69721
|
Fri Jan 19 15:49:13 2024 |
| Frank Heyroth | heyroth(at)cmat.uni-halle.de | Bug report | Linux | 3.1.4 | user change under webserver authentication not recognized |
Hi all,
I am using the Apache webserver authentication and redirection over http (not https). I have configured it 1:1 as described in the Adminguide. In the elog.cfg I set Authentication = Webserver.
All works fine; the webserver requests an authentication and elog recognizes me correctly.
However, when I close and reopen the browser and log in as a different user, elog does not change the user (tested with Firefox and Edge).
I can only change the user if I use a different browser or restart the elogd (reload is not enough).
The X-Forwarded-User header is set to the correct username - I have checked it with a CustomLog in Apache.
Best regards,
Frank |
|
69727
|
Sun Feb 18 11:43:07 2024 |
| James | richo-sm@outlook.com | Question | Linux | Windows | 3.1.4 | Webserver Auth Method and Self Registration |
Hi there. I have been testing a set-up of elog behind an Apache reverse proxy using the Webserver auth method. Apache has been configured for LDAPS with Active Directory allowing us to restrict Elogs by AD group, something not able to be done with the LDAP module.
Testing with Elog 3.1.4 (on Windows) and also Elog 3.1.5 (compiled on Ubuntu 20.04) I experience an issue that when the user logs in for the first time using the above they get the self registration box asking for name and email, and then once they hit save they get an error that says: "Error: Command "Config" not allowed". Once the error is dismissed it never comes back, but its confusing for users who call for help when they first see it.
Is there a way to skip the self registration with the Webserver auth method? and if not is there a reason for the error?
Attached is a copy of the error and an elog config file. Any ideas?
PS. As a side piece the logout options for Webserver needs some enhancement, maybe an option to close the web browser or tab so that it does not retain the logged in cookies. |
|
69774
|
Mon Apr 8 15:46:49 2024 |
| Nick Sauerwein | nick.sauerwein@luxtelligence.ai | Info | Linux | 3.1.4 | Extendable list of numeric items |
Hey eloggers,
I am setting up an ELOG to log the cleanroom fabrication in our startup (Luxtelligence SA). The fabrication is structured in different process steps that are performed by several wafers at the same time (each wafer as an ID).
I am looking for an possibility to put a list of several integers as one of the attributes.
Here an example:
Attributes = Batch ID, Wafer IDs
Type Batch ID = numeric
Type Wafer IDs = extendable list of numeric values
Does something like this exsist?
Thanks in advance for your help. |
|
69775
|
Mon Apr 8 17:08:11 2024 |
| John Kelly | john@secondcomingtechnologies.com | Info | Linux | 3.1.4 | Re: Extendable list of numeric items |
Hi Nick,
If I understand your question correctly maybe this might help:
Search for 'attribute' and you will find this:
"some attributes may be pre-filled from system variables (like your user name). Pre-filled attributes may be still editable or read-only (like the entry creation date.
Attributes may be text fields (limited to 100 characters), list-boxes (max. 100 values), or check-boxes. There is also a special type of attribute where several values are listed on a line with check-boxes, and you can check as many values as needed."
I guess this above is like creating an attribute field, that has attribute names. I *thought* there was a way to leave attributes open where users could create their own 'attribute' names, but the information above is all of what I remember from my past in depth work with Elog.
John
| Nick Sauerwein wrote: |
|
Hey eloggers,
I am setting up an ELOG to log the cleanroom fabrication in our startup (Luxtelligence SA). The fabrication is structured in different process steps that are performed by several wafers at the same time (each wafer as an ID).
I am looking for an possibility to put a list of several integers as one of the attributes.
Here an example:
Attributes = Batch ID, Wafer IDs
Type Batch ID = numeric
Type Wafer IDs = extendable list of numeric values
Does something like this exsist?
Thanks in advance for your help.
|
|