ID |
Date |
Author |
Subject |
Text |
 |
|
705
|
Tue Jun 19 12:54:51 2018 |
Phan Van Chuan | The data acquisition speed | Thank Stefan Ritt, I added the SoftTrigger()
just after StartDomino(), so now, The data
acquisition speed the same speed as in the |
|
|
704
|
Tue Jun 19 10:05:50 2018 |
Stefan Ritt | The data acquisition speed | How do you tigger the board? In your code
below you start the board (StartDomino())
and then wait for a trigger. Setting the |
|
|
703
|
Tue Jun 19 06:42:23 2018 |
Phan Van Chuan | The data acquisition speed | Dear Stefan,
We are using an DRS4 board V5.1
for building a metering system for the scintillator |
|
|
702
|
Wed Jun 13 16:34:28 2018 |
Julian Kemp | Maximum analog input voltage | Thank you! That solves my problem.
|
|
|
701
|
Wed Jun 13 13:42:47 2018 |
Stefan Ritt | Maximum analog input voltage | In principle the numbers in the manual
are correct. But they relate to pulses of
a certain length, because the input protection |
|
|
700
|
Wed Jun 13 13:23:17 2018 |
Julian Kemp | Maximum analog input voltage | Dear all,
I have been wondering what the
maximum analog input voltage for the DRS4 |
|
|
699
|
Fri Jun 8 08:11:05 2018 |
Stefan Ritt | | Several people reported this problem, but
we cannot reproduce it at our lab. Both the
oscilloscope and the command line interface |
|
|
698
|
Thu Jun 7 16:27:21 2018 |
Phan Van Chuan | | Dear Stefan,
I am using an DRS4 board to test
the signal from an scintillator detector; |
|
|
697
|
Thu May 17 13:29:34 2018 |
Stefan Ritt | "Symmetric spikes" fixed | Good news for all DRS4 users. After many
years, I finally understand where the "symmetric
spikes" come from and how to fix them. |
|
|
696
|
Mon May 14 09:21:29 2018 |
Alessio Berti | WIndows Connection problem with drs507 SOLVED | Hi,
I have a machine with Windows 10
and the solution provided by Steven works |
|
|
695
|
Wed May 9 14:07:10 2018 |
Alec Shackleford | WIndows Connection problem with drs507 SOLVED | Thank you for this fantastic solution.
I had almost reinstalled windows 7 to see
if that would solve the issue! |
|
|
694
|
Wed May 9 09:03:52 2018 |
Stefan Ritt | Manual Rev5.1 Figure 1, optional components | I updated the picture in the manual with
a current picture of a Rev5.1 board, and
also added a picture of the bottom side. |
|
|
693
|
Tue May 8 23:58:35 2018 |
Sean Quinn | Manual Rev5.1 Figure 1, optional components | Dear All,
I'm troubleshooting a board |
|
|
692
|
Tue May 8 14:43:03 2018 |
Stefan Ritt | Peak at 0 mV in traces | The DRS chip is read out with a 12 bit
ADC, thus the phyical resolution is roughly
1V/4096 = 0.24 mV. I say roughly since the |
|
|
691
|
Tue May 8 12:15:54 2018 |
Alessio Berti | Peak at 0 mV in traces | Hi Stefan,
following your example, we tried
to perform the same measurement, using drs_exam |
|
|
690
|
Sun May 6 11:45:09 2018 |
Stefan Ritt | confusion about the description in drs.cpp | The locbus_addr is indeed 32 bits wide,
since the firmware was originally derived
from some firmware running in a VME crate, |
|
|
689
|
Sun May 6 08:13:37 2018 |
chen wenjun | confusion about the description in drs.cpp | Hi Stefan:
I'm still confused that
althought the 8 bits buffer is enough,the |
|
|
688
|
Fri May 4 12:11:57 2018 |
Stefan Ritt | Running drs_example.cpp | And here is the second part of your answer:
When you change the input range, you have
to redo the voltage calibration. Best is |
|
|
687
|
Fri May 4 11:56:08 2018 |
Stefan Ritt | Voltage and Timing Calibration in drs_exam.cpp | Have you set the sampling frequency
b->SetFrequency(5, true);
before the calibration? |
|
|
686
|
Fri May 4 11:35:20 2018 |
Stefan Ritt | Peak at 0 mV in traces | I tried the following:
- trigger on a 10 MHz sine wave
on CH0, CH1 was open |
|