| ID |
Date |
Author |
Subject |
Text |
 |
|
634
|
Wed Oct 18 09:12:26 2017 |
Stefan Ritt | Time offset | No this is not possible. But you can delay
your signal externally (like with a delay
cable or electronically) and then send the |
|
|
635
|
Wed Oct 18 11:48:14 2017 |
Vadym Denysenko | Time offset | Thank you for your reply!
|
|
|
877
|
Fri Mar 11 17:26:15 2022 |
Matias Senger | Time calibration and the C++ API | I am using the V5 board at a fixed sampling
frequency. With the `drsosc` app I have executed
the time calibration at 5 GS/s (actually |
|
|
878
|
Sat Mar 12 10:13:24 2022 |
Stefan Ritt | Time calibration and the C++ API | DRSBoard::GetTime is declared in DRS.h
line 720.
If you want to measure timing down |
|
|
879
|
Sat Mar 12 16:52:36 2022 |
Matias Senger | Time calibration and the C++ API | Dear Stefan,
For the time of each bin I am using
the values returend by `GetTime` without |
|
|
880
|
Mon Mar 14 08:59:51 2022 |
Stefan Ritt | Time calibration and the C++ API | Looks like you have the some time calibration,
not sure if it's the correct one. Sample
the sine wave from the calibration clock, |
|
|
881
|
Tue Mar 15 13:07:50 2022 |
Matias Senger | Time calibration and the C++ API | Thanks for your help. If I look into the
app the behavior for the 4 channels is exactly
as you show: |
|
|
651
|
Wed Jan 17 09:51:16 2018 |
Tran Cong Thien | The input signals recorded are different with the signal showed in oscilloscope | Dear Stefan,
I am using an DRS4 board to record
the signals from an plastic scintillator |
|
|
652
|
Wed Jan 17 10:09:09 2018 |
Stefan Ritt | The input signals recorded are different with the signal showed in oscilloscope | First thing is to do another voltage calibration.
Disconnect input, "Config", "Execute
Voltage Calibration". If this does not |
|
|
340
|
Thu Apr 17 12:02:28 2014 |
Wang | The first channel is wrong. | Hi, |
|
|
703
|
Tue Jun 19 06:42:23 2018 |
Phan Van Chuan | The data acquisition speed | Dear Stefan,
We are using an DRS4 board V5.1
for building a metering system for the scintillator |
|
|
704
|
Tue Jun 19 10:05:50 2018 |
Stefan Ritt | The data acquisition speed | How do you tigger the board? In your code
below you start the board (StartDomino())
and then wait for a trigger. Setting the |
|
|
705
|
Tue Jun 19 12:54:51 2018 |
Phan Van Chuan | The data acquisition speed | Thank Stefan Ritt, I added the SoftTrigger()
just after StartDomino(), so now, The data
acquisition speed the same speed as in the |
|
|
140
|
Wed Dec 14 00:44:37 2011 |
Hao Huan | Synchronization Delay in the Firmware for 8051 Controller | Hi Stefan,
I have a question
regarding the DRS 4 evaluation board firmware |
|
|
141
|
Wed Dec 14 08:55:29 2011 |
Stefan Ritt | Synchronization Delay in the Firmware for 8051 Controller |
|
|
|
600
|
Thu Apr 13 16:42:21 2017 |
Christian Farina | Stand-alone Time Calibration for PSI Board | Hello everybody,
I was trying to create a stand-alone
program that would perform a time calibration |
|
|
601
|
Thu Apr 13 16:50:18 2017 |
Stefan Ritt | Stand-alone Time Calibration for PSI Board | Hard to say. Timing calibration is quite
delicate. If you start from scratch, better
read this paper: https://arxiv.org/abs/1405.4975 |
|
|
602
|
Thu Apr 13 16:54:32 2017 |
Christian Farina | Stand-alone Time Calibration for PSI Board | Hi Stefan,
Thank you for your reply. I have
read the paper already. I looked through |
|
|
603
|
Thu Apr 13 17:02:01 2017 |
Stefan Ritt | Stand-alone Time Calibration for PSI Board | Than you can try to isolate the code. Note
that different SCAs might work differently.
Like the DRS4 has a channel-to-channel jitter |
|
|
604
|
Thu Apr 13 17:10:58 2017 |
Christian Farina | Stand-alone Time Calibration for PSI Board | Thank you for your help Stefan. I will
try to get the TC part isolated.
|
|